Toolpaths from the part, held to the machine.

The feeds come from the tool, the material and the machine's ceilings. A flat outline is planned here in milliseconds; a solid goes to FreeCAD's Path.

Una placa de soporte en el modo CAM de la app 3D: Generar escribe el G-code y la simulación lo corta línea a línea entre las mordazas.
Recorded in the workbench: a bracket plate in the 3D app's CAM mode, cut line by line in simulation.

Case study 1 · the speed and the feed

The spindle is the limit, so the feed follows it.

UpperBody-001's lamp plate is 92 × 46 × 3 mm of aluminium. The fleet's 3018 routers carry a 180 W spindle. Its kit page gives 7,000 rpm at 24 V, which no unit has measured. Aluminium wants a faster spindle, so the feeds engine ran it at that ceiling and worked the feed out from it, keeping the chip load.

The engine also said what a machinist would: a full-width slot has nowhere for its chips to go, so take a lighter depth than a profile pass, or cut it trochoidally.

, held at the machine's ceiling
7,000 rpm
feed for a 3.175 mm two-flute end mill
370 mm/min
chip per tooth
0.026 mm
of cutting power, of the spindle's 180 W
4.7 W
ProcedenciaArchivo cloud://home/user-commandagi/case-studies/cam/lamp-plate-feeds.call.jsonEjecución runs/20261107t113132z-lamp-plate-feedsHerramienta fab_feedsSe ejecutó en This computer (dell-gb10-1)Cuándo

Case study 2 · the outline and the holes

Ten passes, four tabs to hold the part.

On the right, fab_mill_region cut the outline free in 0.3 mm passes and left four tabs, so the plate does not come loose into the cutter on the last pass. On the left, FreeCAD's Path contoured and drilled the same plate from the module's own solid in Body.3d.tsx. The picture draws the depth four times its size, from runs 20261107t113120z-lamp-plate-contour, 20261107t113126z-lamp-plate-drill and 20261107t113136z-lamp-plate-profile.

passes through 3 mm
10
of cut, about 7.8 min at 370 mm/min
2,887 mm
tabs, holding 16 mm of the outline
4
holes of Ø3.4, pecked 0.5 mm at a time
2
Dos trayectorias para la placa de lámpara de aluminio de UpperBody-001, vistas en ángulo con la profundidad dibujada cuatro veces su tamaño: a la izquierda el contorno de FreeCAD bajando en anillos finos y dos taladrados en ámbar en los agujeros; a la derecha el perfil en azul, con sus últimas pasadas subiendo sobre cuatro pestañas de sujeción.
ProcedenciaArchivo cloud://home/user-commandagi/case-studies/cam/lamp-plate-profile.call.jsonEjecución runs/20261107t113136z-lamp-plate-profileHerramienta fab_mill_region (the picture also draws the drill run 20261107t113126z-lamp-plate-drill)Se ejecutó en This computer (dell-gb10-1)Cuándo

What the machine would get

Two programs for grbl, zeroed at the stock's corner.

The contour and the drilling are each one program, posted for the grbl controller of the 3018. The plate sits at Z 532 mm in the module's assembly, so the export moves each program to the stock's own origin: X0 Y0 Z0 is the stock's low corner, and the program's first line says where that corner was in the part's frame (X37.000 Y61.700 Z531.950). The stock is the plate with 5 mm past it on each side. Both programs are then held to the 3018's 300 × 180 × 45 mm envelope. Every program says unvalidated: no part has been cut with it on a real machine, and sending it to one is a separate, granted act. Not fabrication-ready.

The first run of this case failed, and said so: with the stock the size of the plate, the contour's tool centre ran 1.59 mm outside it, to X −1.587, and the envelope check refused the program. The cause was that the route knew no stock beyond the part. It now takes the stock's margin (stockMargin).

lines in the contour program, from X 3.4 to 98.5 mm, Y 3.4 to 52.6 mm and Z −1 to 9 mm
201
lines in the drilling program, from X 8.0 to 94.0 mm and Z 0 to 9 mm
123
of stock past the plate on each side
5 mm
of the fleet's routers commissioned
0
ProcedenciaArchivo cloud://home/user-commandagi/case-studies/cam/lamp-plate-contour.call.jsonEjecución runs/20261107t113120z-lamp-plate-contourHerramienta fab_cam: FreeCAD Path in cam-eval, grbl postSe ejecutó en This computer (dell-gb10-1)Cuándo

Plan a cut on your machine.

Name the tool, the stock and the machine. An agent plans the path and says when a number would break a tool.